Programmable Control For Home Safety via GSM Remote
Friday 27 April 2012
WEEK 14: ENGINEER DAY'S ( FYP PRESENTATION)
Objectives:
To test a level of understanding for my final year project.
To present about programmable control home safety via gsm modem; the performance or what have been achieved.
To improve myself, in term of knowledge, presentation and communication.
Content / Procedure:
Refer to FYP scheme, presentation degree semester 2 to prepare a material.
Discuss with supervisor, about how to tackle the question.
Done a more research about basic knowledge of GSM modem and program microcontroller.
Prepare a video as an supported material
Ensure the prototype in high good condition.
Result and Analysis:
I'm done a slideshow, poster and a few testing towards hydro prototype to ensure it work properly during presentation.
The presentation will be conducted by 2 referee.
My presentation considerably good and smooth.
The poster and pictures for presentation shown below:
Conclusions
Personally, i'm glad that i be able to complete my FYP project until achieved the goal because of some difficulty to find a reference and so on.Then i got top 20 in BMI.Alhamdulillah.
This project programmable control home safety via gsm modem takes more effort to make it with excellent.
This project can be develop into another level if the new candidate; who have an interest towards control the appliances in the house to spend an effort, time and money to make it more useful.
Friday 20 April 2012
WEEK 13
Title:
Preparation for the presentation day.
Presentation Day
Objective:
To prepare the presentation Poster.
To present the project of "Progammable control home safety via GSM modem" that will be contributes 10% of the coursework.
Contents / Procedures: The presentation day is on Week 14, Thursday, April 24, 2012. The presentation day is held at three places which is Dewan Gemilang, TTL foyer and academic building at level 2 and level 3. The project of mine will be access by Madam Nazariah and Dr.Ahmad Basri. Before the presentation, the poster show has been shown to the supervisor, Tuan haji Dr Zainudin bin Kornain.
Results: The event is going smoothly and during the presentation time, assessors ask some question regarding on the project.
This my poster.
Friday 13 April 2012
WEEK 12
Title: Show all the circuit and prototype to advisor.
Objective:
To verify my project to advisor.
Result and Analysis:
My advisor verify and said well done.
Objective:
To verify my project to advisor.
Result and Analysis:
My advisor verify and said well done.
Friday 30 March 2012
WEEK 11
Title:
Final Year Project briefing.
Objective:
To gain knowledge from the briefing.
Contents / Procedures:
For this week, there is Final Year Project briefing at TTL 1. The committee is Dr Mohd Khairil bin Rahmat and Mr Shamsul Zahari bin Shahidin. Some point of the briefing is on the T-Shirt, claiming budget and submission of the report for FYP Sem 2 and Diploma students. Plus, to reminds the students on the presentation day for Degree Sem 1 and Engineers Day for Degree Sem 2 and Diploma students.
Friday 23 March 2012
Friday 16 March 2012
WEEK 9
Title: Troubleshooting all circuit
Objectives:
To analyse the circuit performance.
Content / Procedure:
All circuit have been brazing.
Do a component test. Collect an old component that have been used in order to reduce a cost.
Try to do some test towards circuit to analyse the performance.
Result and Analysis:
Have some circuit have problem because of some component burn or damage.
Objectives:
To analyse the circuit performance.
Content / Procedure:
All circuit have been brazing.
Do a component test. Collect an old component that have been used in order to reduce a cost.
Try to do some test towards circuit to analyse the performance.
Result and Analysis:
Have some circuit have problem because of some component burn or damage.
Wednesday 7 March 2012
WEEK 8
Objectives:
> To make a circuit PCB etching and drilling.
> To Test a PCB Inverter circuit.
> To analyse the circuit performance.
Content / Procedure:
> Prepare a material to do circuit etching.
> Do a component test. Collect an old component that have been used in order to reduce a cost.
> Try to do some test towards etching circuit to analyse the performance.
Result and Analysis:
I'm done a construction for High Current Inverter Circuit. The circuit is fly-back converter and using 555 timers as an controller.
This testing part was done by using my old equipments that have been used during my studies.
The circuit PCB design and the pictures during etching the inverter circuit.
Subscribe to:
Posts (Atom)